Glass beads: Pending tutorial Dal1

Dal1 slope

With these slopes we are going to combine the use of pins and the lined up one with nylon

Materials

- Pebbles

- 14 Tupi of 4mm of crystal of Swarovski

- Thread nylon 0,3mm

- Pin of slope and slope hook

- Tools: pliers of round end

STEP 1

We lined up 8 pebbles in the thread

STEP 2

We crossed the thread by 2 last pebbles

STEP 3

In one of threads (p.e drcho.) we lined up 1 tupi (1) and 2 pebbles

STEP 4

We crossed 2 threads by a second tupi (2) and the thread that leaves by the part down we passed it through 2 adjacent pebbles

STEP 5

In the thread that leaves by the part above tupi we lined up 2 pebbles and tupi (3)

STEP 6

We crossed threads by tupi3 and the thread of down we passed it through 2 adjacent pebbles

STEP 7

In the thread that leaves by above tupi3 we lined up 2 pebbles and tupi (4)

STEP 8

We crossed 2 threads by tupi4 and passed threads through the 2 pebbles that lack as well as by tupi which we put in step 3

STEP 9

We crossed threads by 2 new pebbles

STEP 10

We are going to repeat the previous steps to make a "second floor" to the piece, so in the thread of right we lined up tupi (5), 2 pebbles and tupi (6)

STEP 11

We crossed threads by tupi 6 and the thread that leaves by down we passed it through the 2 pebbles that there are down to left beaten

STEP 12

In the thread that leaves by above in tupi 6 we lined up 2 pebbles and tupi (7)

STEP 13

We crossed threads by tupi 7 and the thread that leaves by down we passed it through 2 adjacent pebbles of down

STEP 14

In the thread that leaves by above tupi 7 we lined up 2 pebbles and tupi (8)

STEP 15

We crossed threads by tupi 8 and the thread that leaves underneath we passed it through adjacent pebbles and tupi that there is opposite (tupi 5) and crossed threads by 2 new pebbles

STEP 16

Again we repeated this sequence to make a third floor (according to the length of the pin that we have we put floors more or less). In the thread of drcha. we lined up tupi (9), 2 pebbles and tupi (10)

STEP 17

We crossed threads by tupi 10 and the thread that leaves downwards we passed it through 2 perpendicular pebbles

STEP 18

In the thread that leaves upwards in tupi 10 we lined up 2 pebbles and tupi (11)

STEP 19

We crossed threads by tupi 11 and the thread that leaves downwards we passed it through 2 adjacent pebbles

STEP 20

In the thread that leaves upwards in tupi 11 we lined up 2 pebbles and tupi (12)

STEP 21

We crossed threads by tupi 12 and the thread that leaves downwards we passed it through 2 pebbles of "down", tupi of opposite (tupi 9), we lined up 2 new pebbles and we make the knot with the other thread, applied glue and we cut the leftovers

STEP 22

We have the "cylinder" of tupis and pebbles that we finished doing, the pin and the hook

STEP 23

We put tupi (13) by the pin of the slope

STEP 24

We put the cylinder and another one tupi (14) by the pin of the slope

STEP 25

With the aid of it tiles of round end we make a curtain ring with the leftover of the pin (leftover must measure 7mm)

STEP 26

We hooked the hook in the curtain ring that we finished doing